EXTREME Overclocking Forums
Home | Reviews | Forums | Downloads | $ EXTREME Deals $ | RealTime Pricing | Free Magazines | Gear | Folding Stats Newsletter | Contact Us


Go Back   EXTREME Overclocking Forums > General CPU Cooling > Water Cooling - (Plain & Chilled)
Register Forum Rules FAQ Search Today's Posts Mark Forums Read

Welcome Guest Visitor! Please Register, It's Free and Fun To Participate!
The EXTREME Overclocking Forums are a place for people to learn how to overclock and tweak their PC's components like the CPU, memory (RAM), or video card in order to gain the maximum performance out of their system. There are lots of discussions about new processors, graphics cards, cooling products, power supplies, cases, and so much more!

You are currently viewing our boards as a "guest" which gives you limited access to view most discussions. You need to register before you can post: click the register link to proceed. Before you register, please read the forum rules. By joining our free community you will have access to post topics, communicate privately with other members (PM), respond to polls, upload your own pictures, and access many other special features. Registration is fast, simple, and absolutely free! To start viewing messages, select the forum that you want to visit from the selection below.

After you have registered and read the forum rules, you can check out the FAQ for more information on using the forum. We hope you enjoy your stay here!

Note To Spammers: We do not allow unsolicited advertising! Spam is usually reported & deleted within minutes of it being posted, so don't waste your time (or ours)!


Please Register to Post a Reply
 
Thread Tools
Old 05-26-2012, 04:20 AM   #1
DarkHayZe
Running System Stock
DarkHayZe's Avatar
Forum Newbie
 
Posts: 17
Last Seen: 06-09-2012
From: Loveland, Co
Koolance RP-452X2 V.2 Question

Does anyone know if the fill ports on the top are G1/4 threaded or not?

Click image for larger version

Name:	rp-452x2_p2-700x700.jpg
Views:	24
Size:	79.6 KB
ID:	163470

My thought is(if it is), of putting in a fill line through the acrylic window on the top of my future case.
United States  Offline
    Register to Reply to This Post
Old 05-26-2012, 08:58 PM   #2
cmdprompt
Budget? What's that?
cmdprompt's Avatar
Regular Member
 
Posts: 44
Last Seen: 11-11-2013
iTrader: 0 / 0%
Here , end of the comments. It's not the same rez but close enough. I believe they are G1/4 threaded, just a little recessed.
United States  Offline
    Register to Reply to This Post
Old 05-27-2012, 05:31 AM   #3
DarkHayZe
Running System Stock
DarkHayZe's Avatar
Forum Newbie
 
Posts: 17
Last Seen: 06-09-2012
From: Loveland, Co
Quote:
Originally Posted by cmdprompt View Post
Here , end of the comments. It's not the same rez but close enough. I believe they are G1/4 threaded, just a little recessed.
Sweet thanks
United States  Offline
    Register to Reply to This Post
Old 06-17-2012, 11:41 PM   #4
xttxtt
Running System Stock
Forum Newbie
 
Posts: 2
Last Seen: 06-18-2012
From: Seattle
They are G1/4 but I would not recommend using a fill tube attached to a fitting on these. I've used this device repeatedly and they are difficult and time consuming to bleed. Adding a fill tube only makes it harder. The best way to fill these is to remove the P1 plug and use a fill bottle or even one of Koolance's cooling fluid bottles with the thin tube. If you add a fill tube attached to a fill port you will contend with milking fluid down into the P1 reservoir thru the attached fill tube, and you'll likely get wet. Once filled, this is a great reservoir/pump combination. If you're using the pumps in series, you'll get better flow than with most other pump/reservoir combinations and it's *very* quiet. Highly recommended if you have the patience to fill it.
United States  Offline
    Register to Reply to This Post
Old 06-24-2012, 08:54 AM   #5
htpcdennis
Learning To Overclock
Regular Member
 
Posts: 71
Last Seen: 09-30-2013
iTrader: 0 / 0%
Yes. I have this res and screwed on a 1/4 barb/pipe to the front for filling.
United Kingdom  Offline
    Register to Reply to This Post
Sponsored Links:
Please Register to Post a Reply


Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

All times are GMT -6. The time now is 11:04 PM.

Copyright 2000 - 2011, Jelsoft Enterprises Ltd.
Powered by vBulletin
Copyright 2000 - 2011, EXTREME Overclocking