| Home | Reviews | Forums | Downloads | $ EXTREME Deals $ | RealTime Pricing | Free Magazines | Gear | Folding Stats | Newsletter | Contact Us |
|
|
|||
|
||||
|
|||||||
| Register | Forum Rules | FAQ | Search | Today's Posts | Mark Forums Read |
| Welcome Guest Visitor! Please Register, It's Free and Fun To Participate! | |
|
The EXTREME Overclocking Forums are a place for people to learn how to overclock and tweak their PC's components like the CPU, memory (RAM), or video card in order to gain the maximum performance out of their system. There are lots of discussions about new processors, graphics cards, cooling products, power supplies, cases, and so much more!
You are currently viewing our boards as a "guest" which gives you limited access to view most discussions. You need to register before you can post: click the register link to proceed. Before you register, please read the forum rules. By joining our free community you will have access to post topics, communicate privately with other members (PM), respond to polls, upload your own pictures, and access many other special features. Registration is fast, simple, and absolutely free! To start viewing messages, select the forum that you want to visit from the selection below. After you have registered and read the forum rules, you can check out the FAQ for more information on using the forum. We hope you enjoy your stay here! Note To Spammers: We do not allow unsolicited advertising! Spam is usually reported & deleted within minutes of it being posted, so don't waste your time (or ours)! |
|
| Please Register to Post a Reply |
|
|
Thread Tools |
05-21-2004, 05:32 PM
|
#1 | ||||
|
Learning To Overclock
Regular Member
|
Barb fittings from home depot, what to get?
Also, how do I properly install the fittings when I have them? PC is a P4 prescott with hyperthreading, ASUS P4P800SE, Danger Den RBX Lucite top for socket 478. |
||||
|
|
|
05-22-2004, 02:16 PM
|
#2 | ||||
|
Learning To Overclock
Regular Member
|
Anyone know? I can't leave it on for too long or it starts to leak a little.
|
||||
|
|
|
05-22-2004, 02:50 PM
|
#3 | ||||
|
Judgement Passed
Senior Member
|
Where is it leaking? The barbs that danger den supplied should be fine. I am still using them. If you do need new ones they are 1/2" barb by 1/4" NPT thread.
|
||||
|
|
|
05-22-2004, 02:55 PM
|
#4 | ||||
|
#6 post whore
Senior Member
|
if your RBX has problems, just contact dangerden about it
|
||||
|
|
|
05-22-2004, 03:11 PM
|
#5 | ||||
|
*Latin Power*
Senior Member
|
I agree with onewecallgod. If you really want to swap out the barbs on the RBX, you'll have to remove the block and losen up the barb from the block. Take the whole thing with you to Home Depot to make sure you get the correct fitting barbs. Get a roll of Teflon tape. Wrap some teflon tape around the threaded part of the barb and screw the sucka into the block nice and snug. DO NOT OVER TIGHTEN! You might strip it and then you'll really be S.O.L. That's all there is to it. Piece of cake
 .
|
||||
|
|
|
05-22-2004, 04:16 PM
|
#6 | ||||
|
Judgement Passed
Senior Member
|
Well mine are epoxied in place, I don't know about yours. There would be no way of me getting them out without cracking the top. I really think you need to tell us where it is leaking.
|
||||
|
|
Sponsored Links:
|
| Please Register to Post a Reply |
| Thread Tools | |
|
|
